Skip to main content

Connector for Pixhawk Family of Flight Controllers

Hirose DF13

Hirose DF13

  • https://www.hirose.com/product/en/products/DF13/
  • 1.25mm pitch
  • -35 ~ 85 deg. C
  • 150 V (AC)
  • AWG 30 ~ 26
  • Pixhawk (PX4FMUv2) uses Hirose DF13 connectors
  • It was designed as a fixed SMT (surface mount) connector with designed mating/unmating cycles of 30~50 times
  • So it is prone to wire and housing breakage
  • Pixhawk copies and even clones often use similarly sized JST SH or Molex PicoBlade, neither of which are compatible with Hirose DF13, causing connector housing breakage, broken pin, and bad connection in general
  • If the connector housing is white, it is safe to assume they are not genuine DF13
  • Below is a picture of an I2C splitter with genuine Hirose DF13
    • I2C Splitter - Hirose DF13

Molex Picoblade

Molex Picoblade

  • http://www.molex.com/molex/products/family?key=picoblade&channel=products&pageTitle=Introduction
  • 1.25mm pitch
  • 125V, 1.0A
  • AWG 26 ~ 32
  • Used in many clones and cheap sensors
  • Can be inserted into DF13 Female headers
  • If you insert DF13 into Picoblade headers, it will most likely break
    • Hirose DF13 v.s. Molex Picoblade
  • Most of the I2C splitters sold on Chinese sites are not DF13. They are usually not even genuine Molex Picoblade and are prone to cracking
    • I2C Splitter
  • This is what an I2C splitter with genuine Hirose DF13 looks like
    • I2C Splitter - Hirose DF13

JST GH

JST GH

  • http://www.jst-mfg.com/product/pdf/eng/eGH.pdf
  • 1.25mm pitch
  • -25 ~ 80 deg. C
  • 50V (AC, DC)
  • AWG 26
  • PixRacer (production version), PXFmini, and newer boards use JST GH Series Connector
  • JST GH has a locking tab with click feedback, are not much larger compared to DF13, and insert direction is easy to identify
  • The crimping terminals are larger than DF13, so custom cables are a little easier to make

JST SH 1.0

JST SH 1.0

  • 1.0mm pitch
  • Smaller than DF13 or Picoblade
  • Used in such FC as CC3D, mini-sized Pixhawks such as Pixfalcon, Pixhawk Mini, etc.

Molex CLICK-Mate

Molex CLICK-Mate

  • Pixhawk 2 (3DR version) and PixRacer beta (prototype) board used Molex CLICK-Mate
  • CLICK-Mate connectors are also used on CAN bus based products
  • It also has locking tab, but are much larger than DF13 or GH connectors

Servo Connectors

Servo Connectors

  • Originally based on Dupont connectors
  • Futaba has extra tabs, but most FC's have a slit that enable you to insert Futaba connectors too
  • However, Futaba uses different size pins and crimp terminals, so if you mix them, female connector may become loose

Making Your Own Cable

These connectors, along with the crimp terminals and crimp tools, can be purchased at RS-Online, Mouser, DigiKey, etc.

Cable Sheath Material

Use of a regular PVC ribbon cable is not advised as they are prone to breakage. Shielded robot cables are OK, but since they are thicker and harder, they tend to pass on the vibrations from the other parts of the vehicle to the floating mounted FC, and sometimes even cause more resonant vibrations.

  • 3DR supplied ribbon cable are pretty good in terms of softness and durability
  • Erle Robotics (PXF, ErleBrain) supplied cables are thin, yet hard
  • AUAV (PixRacer) supplied cables have nice soft silicone sheath, but they are too thick to hand crimp into the connector housing
  • Many GPS and other modules bought from China comes with robot cable with hard outer sheath. Make sure you build a strain relief at the Pixhawk end to prevent individual wires from breaking off
  • The best cable that I've encountered so far is a silicone ribbon cable that came with one of the sensors, but they are hard to find

References